13757158604 刘总
15168473000 王总
微信二维码
手机端官网
  • 外墙保温板怎么样粘贴
  • 本站编辑:杭州博恩环保科技有限公司发布日期:2019-05-06 09:58 浏览次数:

外墙保温板在生活使用中并不陌生,作为新型的建筑材料,外墙保温板专指用于建筑墙体的一类保温材料,下面杭州博恩环保科技有限公司就带我们一起了解一下外墙保温板粘贴的注意事项有哪些吧:

  1、外墙保温板某一面因包装、运输等原因造成微小的缺陷时,则应将这一面作为抹胶面。

  2、将涂抹好胶粘剂的保温板紧密地粘贴在墙面上(或插入托架),在粘贴下一块保温板时,应将这块板从侧面推压向前一块板,并保证保温板与保温板之间的接缝被压紧。在墙角托架处,玻璃纤维网格布应延伸至托架的底边边缘,多余部分用刀切除。

  3、保温板间高差不得大于1.5㎜(或4㎜/2m),当保温板间高差有大于1.5㎜的部位,应在粘胶硬化后做轻柔圆周运动打磨平整。

外墙保温板


  4、粘贴保温板缝应轻揉,均匀挤压、挤紧,保温板缝应错开,相邻外墙保温板应齐平,粘结砂浆挤出时用铲刀必须立即刮掉,使保温板与保温板之间无“碰头灰”。

  保温板间缝隙不得大于2㎜,保温板缝隙大于2㎜时,应用保温板条将缝塞满,保温板条不得粘结,更不得用胶粘剂直接填缝。

  以上就是关于外墙保温板在粘贴时注意的事项,杭州博恩环保科技有限公司 就是经营外墙保温板的,如果你有相关的需要欢迎咨询我们。


l2-161215141025_180_134[1].jpg

The external wall insulation board is not unfamiliar in the use of life. As a new type of building material, the external wall insulation board specifically refers to a type of insulation material used for building walls. The following Hangzhou Boen Environmental Protection Technology Co., Ltd. will take us to understand the external wall insulation board. What are the points of note for pasting:
When one side of the external wall insulation board causes minor defects due to packaging, transportation, etc., this side should be used as a rubber surface.
2, the coated adhesive insulation plate is closely affixed to the wall(or inserted into the bracket), when pasting the next plate, this plate should be pushed from the side of the forward plate, and ensure that the insulation board and the interface between the plate is pressed. At the corner bracket, the fiberglass mesh cloth should be extended to the bottom edge of the bracket, and the excess parts should be removed with a knife.
3, the difference between the insulation board must not be greater than 1.5 <UNK>(or 4 <UNK> / 2m), when the difference between the insulation board is greater than 1.5 <UNK>, soft circular motion grinding should be done after the adhesive hardens.
External wall insulation board
4, paste the insulation board seams should be gently rubbed, evenly squeezed, squeeze, insulation board seams should be staggered, adjacent external wall insulation board should be flat, glue mortar extrusion with a shovel knife must be immediately scraped off, so that the insulation board and the insulation board There is no "meeting ash."
The gap between the insulation board must not be greater than 2 <UNK>, when the gap between the insulation board is greater than 2 <UNK>, the insulation board is applied to fill the seam, the insulation board is not bonded, and the adhesive is not used to fill the seam directly.
The above is about the external insulation board in the pasting matters, Hangzhou boan environmental protection technology Co., Ltd. is operating external insulation board, if you have relevant needs welcome to consult us.